|Gang Programmer ¦|
|Auto. Handler System|
| Sockets and Accessories|
|Eprom Eraser, IC Tester|
|Jig test ICT/FCT/DIP-pallet|
|Test and Measurement|
|Osciloscope, HDS, MSO|
|Data Logger and Sensors|
|Generator, Freq. couter|
|LCR, component tester|
|Power Supply, elec. load|
|Design, Assembly Tools|
|Training & Education KIT|
|Embedded Dept. Tools|
|Rework & Solder tools|
|SMT/ PCBA Equipments|
|Other electronics Tools|
|Optical, Force, Torque|
|MCU 8051-core series |
|Nuvoton ARM Cortex-M|
|Voice and Audio ICs|
|Nuvoton ARM7/9 Soc|
|Wireless RF IC, Tools|
|We received |
page views since 20/12/2006
There are currently, 0 guest(s) and 0 member(s) that are online.
You are Anonymous user. You can register for free by clicking here
Category: Main/1. Device Programmer - Introduction and Guide/1.8. Accessories, cables and socket adapters
| ◊ Đặc điểm chính:|
- top board of TSOP48 adapters (mainly FLASH EPROM with 48-pins)
- operating (mechanical) warranty of ZIF socket - 10,000 actuations
|Socket||ZIF TSOP48, OpenTop type|
|Bottom||2x24 + 1x3 pins, square, 0.6x0.6mm|
- For work with TSOP48 device it is necessary put together Top TSOP48 ZIF 18.4mm with some Bottom TSOP48-x board according to the information provided by PG4UW software.
- The picture show, how to put together the Top TSOP48 ZIF 18,4mm and Bottom TSOP48-x boards to have complete TSOP48 adapter.
- Insert comlete adapter to the device programmer ZIF socket according to the picture placed near of it. If you have some doubts about orientation of this adapter in device programmer ZIF socket, it is valid general rule, the orientation of the text of title is the same as the text on the top of the device programmer.
- Push the top of adapter ZIF socket to open it. Insert the device into the adapter ZIF socket. The right position of the programmed device in adapter ZIF socket is show at picture near (mainly left above) the adapter ZIF socket. Then release adapter ZIF socket.
- Visually check interconnection between device and adapter ZIF socket. If everything looks OK, the device is ready for programming.
- Be careful, because the incorrect insertion of adapter to the device programmer ZIF socket or device to the adapter ZIF socket can damage the programmed device.
- To take out the device push the top of adapter ZIF socket and remove device from it.
- When you finish work with adapter, remove it from the device programmer ZIF socket.
- Do not directly touch the pins of the adapter and adapter ZIF socket, because dirt may cause errors during programming of device.
- For handling with the device we recommended to use a vacuum pick up tool.
- Operation conditions: operating temperature 5°C ÷ 40°C (41°F ÷ 104°F), operating humidity 20%..80%, non condensing.
CÁC SẢN PHẨM KHÁC CÙNG NHÀ SẢN XUẤT / OTHER PRODUCTS FROM ELNEC
OUR GLOBAL PARTNERS
Minato, Leap, SMH-Tech, Xeltek, Elnec, Conitec, DediProg, Phyton, Hilosystems, Flash Support Group, PEmicro ||
Rigol, Tonghui, Copper Mountain, Transcom, APM || Atten, Zhuomao, Puhui, Neoden, Ren Thang, Genitec, Edry, UDK ||
CONDITTION AND USING TERMS
TULA Solution Co., Ltd - Công ty TNHH Giải pháp TULA
Headquater: No. 173 Group 15, Dong Anh District, Hanoi 10000, Vietnam
Head-Office: No. 6 Lane 23, Đình Thôn street, Mỹ Đình ward, Nam Từ Liêm Dist., Hà Nội, Vietnam
Tel.: +84-24.39655633, Hotline: +84-912612693, E-mail: info (at) tula.vn